China Double Row Spherical Roller Bearing with Brass Cage NTN NSK Koyo NACHI Timken Bearing 23248 Ca/W33 bearing block

Merchandise Description

Bearing of this kind has 2 rows of spherical rollers in between the sphered raceway in the outer ring and 2 inner rings raceways inclined at an angle to the bearing axis.According to the big difference of the bearing interior composition, there are 5 kinds of cages:CA,MA,CC,E and CTN1.Owing to the arc middle of the raceways in the ourter ring and the bearing center are in the very same direction, as a result, shaft flexing and misalignment of the bearing seats are compensated. Bearings of this sort  can help axial forces in the two directions and high radial forces. They are created for really higher load carrying capability. Bearings with a tapered bore are also accessible with an adapter sleeve, locknut and tab washer or with a withdrawal sleeve.When shaft bends by drive which causes the inclined among the center of internal ring and the center of outer ring,if the inclined diploma not exceed 1-2.5,the bearing can operate normally.
This series is available in tapered bore – suffix “K” (taper 1:12).
1) Suffix “W/33” – lubrication groove and holes in outer ring.
two) C/3, C/4, and C/5 inside clearances are also obtainable

Bearing NO.  
New : 23248CA/W33
Old : 357148KH
Boundary proportions(mm)  
d : 240
D : 440
B : one hundred sixty
r 1.2min : 4
Simple load ratings(kN)  
Cr : 2440
Cor : 4050
Restricting pace(rpm)  
Grease : 630
Oil : 800
Abutment and fillet proportions(mm)  
da min : 258
Da max : 422
ra max : three
Value  
e : .37
Y1 : one.eight
Y2 : two.7
Y0 : 1.eight
Bodyweight (kg)  
Refer : 106

—222 series
—223 series
—230 collection
—231 sequence
—232 sequence
—239 collection
—240 series
—241 series
—BS2 sequence
—SB-222 sequence
—SB-223 series 
Cage Accessible:CA,CC,MB,MA,E,E1 
Sealing Sort:Open up&sealed
Cage Material:Brass&pressed steel

Warehouse 

 

Bearing No. Boundary Proportions  Basic Loading(kN)  Limiting Velocity(rpm) Mass(kg)
  dxDxB Dy.(Cr) Sta.(Cor) Grease Oil  
23034CA/W33 170x260x67 555 1090 1600 2000 fourteen.2
23034MB/W33 170x260x67 555 1090 1600 2000 14.2
23034CC/W33 170x260x67 555 1090 1600 2000 14
23134CA/W33 170x280x88 730 1390 1200 1600 26.one
23134MB/W33 170x280x88 730 1390 1200 1600 26.1
23134CC/W33 170x280x88 730 1390 1200 1600 twenty five.six
23234CA/W33 170x310x110 1070 1930 950 1300 38
23234MB/W33 170x310x110 1070 1930 950 1300 38
23234CC/W33 170x310x110 1070 1930 950 1300 37.five
23934CA/W33 170x230x45 four hundred 800 1800 2400 5.45
23334CA/W33 170x360x136 1420 2250 900 1200 sixty eight.7
23334MB/W33 170x360x136 1420 2250 900 1200 sixty eight.7
24134CA/W33 170x280x109 915 1830 a thousand 1400 24.8
24134MB/W33 170x280x109 915 1830 a thousand 1400 24.eight
24134CC/W33 170x280x109 915 1830 a thousand 1400 24.1
24034CA/W33 170x260x90 705 1500 one thousand 1400 seventeen.eight
24034MB/W33 170x260x90 705 1500 1000 1400 17.eight
24034CC/W33 170x260x90 705 1500 a thousand 1400 seventeen.1
22234CA/W33 170x310x86 845 1450 1300 1700 26.8
22234MB/W33 170x310x86 845 1450 1300 1700 26.eight
22234CC/W33 170x310x86 845 1450 1300 1700 26.1
22334CA/W33 170x360x120 1320 2120 950 1300 62.6
22334MB/W33 170x360x120 1320 2120 950 1300 62.6
22334CC/W33 170x360x120 1320 2120 950 1300 sixty two.1
23036CA/W33 180x280x74 630 1280 1400 1800 seventeen.seven
23036MB/W33 180x280x74 630 1280 1400 1800 17.seven
23036CC/W33 180x280x74 630 1280 1400 1800 seventeen.4
23136CA/W33 180x300x96 900 1720 1100 1500 27.one
23136MB/W33 180x300x96 900 1720 1100 1500 27.1
23136CC/W33 180x300x96 900 1720 1100 1500 26.six
23236CA/W33 180x320x112 1160 2130 900 1200 38.7
23236MB/W33 180x320x112 1160 2130 900 1200 38.seven
23236CC/W33 180x320x112 1160 2130 900 1200 38.four
23936CA/W33 180x250x52 430 830 1700 2200 7.34
23936CC/W33 180x250x53 430 830 1700 2200 seven.34
24136CA/W33 180x300x118 1571 2030 900 1200 33
24136MB/W33 180x300x118 1571 2030 900 1200 33
24136CC/W33 180x300x118 1571 2030 900 1200 32.7
24036CA/W33 180x280x100 835 1750 950 1300 26.six
24036MB/W33 180x280x100 835 1750 950 1300 26.six
24036CC/W33 180x280x100 835 1750 950 1300 26.two
22236CA/W33 180x320x86 895 1550 1300 1700 29.4
22236MB/W33 180x320x86 895 1550 1300 1700 29.four
22236CC/W33 180x320x86 895 1550 1300 1700 29.1
22336CA/W33 180x380x126 1470 2400 900 1200 72.two
22336MB/W33 180x380x126 1470 2400 900 1200 72.2
22336CC/W33 180x380x126 1470 2400 900 1200 seventy two
23038CA/W33 190x290x75 seven-hundred 1450 1300 1700 17.3
23038MB/W33 190x290x75 seven hundred 1450 1300 1700 17.3
23038CC/W33 190x290x75 700 1450 1300 1700 seventeen.one
23138CA/W33 190x320x104 975 1840 one thousand 1400 34.3
23138MB/W33 190x320x104 975 1840 1000 1400 34.three
23138CC/W33 190x320x104 975 1840 one thousand 1400 34
23238CA/W33 190x340x120 1290 2400 850 1100 44.8
23238MB/W33 190x340x120 1290 2400 850 1100 forty four.8
23238CC/W33 190x340x120 1290 2400 850 1100 forty four.4
23938CA/W33 190x260x52 550 980 1500 2000 8.32
23938CC/W33 190x260x52 550 980 1500 2000 eight.01
24138CA/W33 190x320x128 1200 2400 850 1100 41.9
24138MB/W33 190x320x128 1200 2400 850 1100 forty one.9
24138CC/W33 190x320x128 1200 2400 850 1100 41.5
24038CA/W33 190x290x100 855 1840 950 1300 22.9
24038MB/W33 190x290x100 855 1840 950 1300 22.nine
24038CC/W33 190x290x100 855 1840 950 1300 22.5
22238CA/W33 190x340x92 865 1620 1200 1600 37.4
22238MB/W33 190x340x92 865 1620 1200 1600 37.four
22238CC/W33 190x340x92 865 1620 1200 1600 37
22338CA/W33 190x400x132 1640 2630 850 1100 82.two
22338MB/W33 190x400x132 1640 2630 850 1100 eighty two.2
22338CC/W33 190x400x132 1640 2630 850 1100 82
23040CA/W33 200x310x82 770 1560 1200 1600 22.6
23040MB/W33 200x310x82 770 1560 1200 1600 22.six
23040CC/W33 200x310x82 770 1560 1200 1600 22.one
23140CA/W33 200x340x112 1170 2240 950 1300 forty three.eight
23140MB/W33 200x340x112 1170 2240 950 1300 43.eight
23140CC/W33 200x340x112 1170 2240 950 1300 forty three.1
23240CA/W33 200x360x128 1360 2530 850 1100 fifty three.four
23240MB/W33 200x360x128 1360 2530 850 1100 53.four
23240CC/W33 200x360x128 1360 2530 850 1100 53.1
23940CA/W33 200x280x60 495 1150 1600 2000 thirteen.two
23940MB/W33 200x280x60 495 1150 1600 2000 13.2
23940CC/W33 200x280x60 495 1150 1600 2000 thirteen
23340CA/W33 200x420x165 2571 3500 750 950 one hundred twenty five
23340MB/W33 200x420x165 2571 3500 750 950 a hundred twenty five
24140CA/W33 200x340x140 1630 2450 900 1200 fifty three.5
24140MB/W33 200x340x140 1630 2450 900 1200 fifty three.5
24140CC/W33 200x340x140 1630 2450 900 1200 53.one
24040CA/W33 200x310x109 985 2130 900 1200 31.3
24040MB/W33 200x310x109 985 2130 900 1200 31.3
24040CC/W33 200x310x109 985 2130 900 1200 31
22240CA/W33 200x360x98 1100 1950 1100 1500 forty four.7
22240MB/W33 200x360x98 1100 1950 1100 1500 forty four.seven
22240CC/W33 200x360x98 1100 1950 1100 1500 forty four.1
22340CA/W33 200x420x138 1740 2860 850 1100 97
22340MB/W33 200x420x138 1740 2860 850 1100 97
22340CC/W33 200x420x138 1740 2860 850 1100 ninety six.6
23044CA/W33 220x340x90 935 1900 1100 1500 32
23044MB/W33 220x340x90 935 1900 1100 1500 32
23044CC/W33 220x340x90 935 1900 1100 1500 31.seven
23144CA/W33 220x370x120 1370 2710 900 1200 54.seven
23144MB/W33 220x370x120 1370 2710 900 1200 fifty four.seven
23144CC/W33 220x370x120 1370 2710 900 1200 fifty four.4
23244CA/W33 220x400x144 1720 3200 750 950 seventy seven.3
23244MB/W33 220x400x144 1720 3200 750 950 seventy seven.three
23244CC/W33 220x400x144 1720 3200 750 950 77
23944CA/W33 220x300x60 five hundred 980 1520 1760 12.five
23944MB/W33 220x300x60 500 980 1520 1760 12.five
23944CC/W33 220x300x60 five hundred 980 1520 1760 twelve.1
24144CA/W33 220x370x150 1920 3045 800 1000 sixty seven
24144MB/W33 220x370x150 1920 3045 800 a thousand sixty seven
24144CC/W33 220x370x150 1920 3045 800 1000 sixty six.6
24044CA/W33 220x340x118 1150 2500 850 1100 39.one
24044MB/W33 220x340x118 1150 2500 850 1100 39.one
24044CC/W33 220x340x118 1150 2500 850 1100 38.seven
22244CA/W33 220x400x108 1350 2400 950 1300 sixty three.five
22244MB/W33 220x400x108 1350 2400 950 1300 63.5
22244CC/W33 220x400x108 1350 2400 950 1300 sixty three.one
22344CA/W33 220x460x145 2450 3130 800 one thousand one hundred fifteen
22344MB/W33 220x460x145 2450 3130 800 one thousand a hundred and fifteen
22344CC/W33 220x460x145 2450 3130 800 1000 115
23048CA/W33 240x360x92 985 2080 one thousand 1400 34.2
23048MB/W33 240x360x92 985 2080 one thousand 1400 34.two
23048CC/W33 240x360x92 985 2080 1000 1400 34
23148CA/W33 240x400x128 1500 3000 850 1100 sixty eight.2
23148MB/W33 240x400x128 1500 3000 850 1100 sixty eight.2
23148CC/W33 240x400x128 1500 3000 850 1100 68
23248CA/W33 240x440x160 2080 3950 750 900 102
23248MB/W33 240x440x160 2080 3950 750 900 102
23248CC/W33 240x440x160 2080 3950 750 900 102
23948CA/W33 240x320x60 530 1310 1300 1700 fifteen
23948MB/W33 240x320x60 530 1310 1300 1700 15
23948CC/W33 240x320x60 530 1310 1300 1700 fourteen.seven
24148CA/W33 240x400x160 1660 3400 800 one thousand 79
24148MB/W33 240x400x160 1660 3400 800 1000 seventy nine
24148CC/W33 240x400x160 1660 3400 800 1000 78.6
24048CA/W33 240x360x118 1240 2800 900 1200 46.five
24048MB/W33 240x360x118 1240 2800 900 1200 46.5
24048CC/W33 240x360x118 1240 2800 900 1200 forty six.1
22248CA/W33 240x440x120 1640 1820 850 1150 85
22248MB/W33 240x440x120 1640 1820 850 1150 eighty five
22248CC/W33 240x440x120 1640 1820 850 1150 84.eight
22348CA/W33 240x500x155 2480 3200 750 one thousand one hundred fifty
22348MB/W33 240x500x155 2480 3200 750 1000 one hundred fifty
22348CC/W33 240x500x155 2480 3200 750 one thousand 149

 

US $415-450
/ Piece
|
1 Piece

(Min. Order)

###

Rolling Body: Roller Bearings
The Number of Rows: Double
Outer Dimension: Extra Large (440mm)
Material: Bearing Steel
Spherical: Aligning Bearings
Load Direction: Radial Bearing

###

Samples:
US$ 415/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:

###

Bearing NO.  
New : 23248CA/W33
Old : 3053248KH
Boundary dimensions(mm)  
d : 240
D : 440
B : 160
r 1.2min : 4
Basic load ratings(kN)  
Cr : 2440
Cor : 4050
Limiting speed(rpm)  
Grease : 630
Oil : 800
Abutment and fillet dimensions(mm)  
da min : 258
Da max : 422
ra max : 3
Value  
e : 0.37
Y1 : 1.8
Y2 : 2.7
Y0 : 1.8
Weight (kg)  
Refer : 106

###

Bearing No. Boundary Dimensions  Basic Loading(kN)  Limiting Speed(rpm) Mass(kg)
  dxDxB Dy.(Cr) Sta.(Cor) Grease Oil  
23034CA/W33 170x260x67 555 1090 1600 2000 14.2
23034MB/W33 170x260x67 555 1090 1600 2000 14.2
23034CC/W33 170x260x67 555 1090 1600 2000 14
23134CA/W33 170x280x88 730 1390 1200 1600 26.1
23134MB/W33 170x280x88 730 1390 1200 1600 26.1
23134CC/W33 170x280x88 730 1390 1200 1600 25.6
23234CA/W33 170x310x110 1070 1930 950 1300 38
23234MB/W33 170x310x110 1070 1930 950 1300 38
23234CC/W33 170x310x110 1070 1930 950 1300 37.5
23934CA/W33 170x230x45 400 800 1800 2400 5.45
23334CA/W33 170x360x136 1420 2250 900 1200 68.7
23334MB/W33 170x360x136 1420 2250 900 1200 68.7
24134CA/W33 170x280x109 915 1830 1000 1400 24.8
24134MB/W33 170x280x109 915 1830 1000 1400 24.8
24134CC/W33 170x280x109 915 1830 1000 1400 24.1
24034CA/W33 170x260x90 705 1500 1000 1400 17.8
24034MB/W33 170x260x90 705 1500 1000 1400 17.8
24034CC/W33 170x260x90 705 1500 1000 1400 17.1
22234CA/W33 170x310x86 845 1450 1300 1700 26.8
22234MB/W33 170x310x86 845 1450 1300 1700 26.8
22234CC/W33 170x310x86 845 1450 1300 1700 26.1
22334CA/W33 170x360x120 1320 2120 950 1300 62.6
22334MB/W33 170x360x120 1320 2120 950 1300 62.6
22334CC/W33 170x360x120 1320 2120 950 1300 62.1
23036CA/W33 180x280x74 630 1280 1400 1800 17.7
23036MB/W33 180x280x74 630 1280 1400 1800 17.7
23036CC/W33 180x280x74 630 1280 1400 1800 17.4
23136CA/W33 180x300x96 900 1720 1100 1500 27.1
23136MB/W33 180x300x96 900 1720 1100 1500 27.1
23136CC/W33 180x300x96 900 1720 1100 1500 26.6
23236CA/W33 180x320x112 1160 2130 900 1200 38.7
23236MB/W33 180x320x112 1160 2130 900 1200 38.7
23236CC/W33 180x320x112 1160 2130 900 1200 38.4
23936CA/W33 180x250x52 430 830 1700 2200 7.34
23936CC/W33 180x250x53 430 830 1700 2200 7.34
24136CA/W33 180x300x118 1020 2030 900 1200 33
24136MB/W33 180x300x118 1020 2030 900 1200 33
24136CC/W33 180x300x118 1020 2030 900 1200 32.7
24036CA/W33 180x280x100 835 1750 950 1300 26.6
24036MB/W33 180x280x100 835 1750 950 1300 26.6
24036CC/W33 180x280x100 835 1750 950 1300 26.2
22236CA/W33 180x320x86 895 1550 1300 1700 29.4
22236MB/W33 180x320x86 895 1550 1300 1700 29.4
22236CC/W33 180x320x86 895 1550 1300 1700 29.1
22336CA/W33 180x380x126 1470 2400 900 1200 72.2
22336MB/W33 180x380x126 1470 2400 900 1200 72.2
22336CC/W33 180x380x126 1470 2400 900 1200 72
23038CA/W33 190x290x75 700 1450 1300 1700 17.3
23038MB/W33 190x290x75 700 1450 1300 1700 17.3
23038CC/W33 190x290x75 700 1450 1300 1700 17.1
23138CA/W33 190x320x104 975 1840 1000 1400 34.3
23138MB/W33 190x320x104 975 1840 1000 1400 34.3
23138CC/W33 190x320x104 975 1840 1000 1400 34
23238CA/W33 190x340x120 1290 2400 850 1100 44.8
23238MB/W33 190x340x120 1290 2400 850 1100 44.8
23238CC/W33 190x340x120 1290 2400 850 1100 44.4
23938CA/W33 190x260x52 550 980 1500 2000 8.32
23938CC/W33 190x260x52 550 980 1500 2000 8.01
24138CA/W33 190x320x128 1200 2400 850 1100 41.9
24138MB/W33 190x320x128 1200 2400 850 1100 41.9
24138CC/W33 190x320x128 1200 2400 850 1100 41.5
24038CA/W33 190x290x100 855 1840 950 1300 22.9
24038MB/W33 190x290x100 855 1840 950 1300 22.9
24038CC/W33 190x290x100 855 1840 950 1300 22.5
22238CA/W33 190x340x92 865 1620 1200 1600 37.4
22238MB/W33 190x340x92 865 1620 1200 1600 37.4
22238CC/W33 190x340x92 865 1620 1200 1600 37
22338CA/W33 190x400x132 1640 2630 850 1100 82.2
22338MB/W33 190x400x132 1640 2630 850 1100 82.2
22338CC/W33 190x400x132 1640 2630 850 1100 82
23040CA/W33 200x310x82 770 1560 1200 1600 22.6
23040MB/W33 200x310x82 770 1560 1200 1600 22.6
23040CC/W33 200x310x82 770 1560 1200 1600 22.1
23140CA/W33 200x340x112 1170 2240 950 1300 43.8
23140MB/W33 200x340x112 1170 2240 950 1300 43.8
23140CC/W33 200x340x112 1170 2240 950 1300 43.1
23240CA/W33 200x360x128 1360 2530 850 1100 53.4
23240MB/W33 200x360x128 1360 2530 850 1100 53.4
23240CC/W33 200x360x128 1360 2530 850 1100 53.1
23940CA/W33 200x280x60 495 1150 1600 2000 13.2
23940MB/W33 200x280x60 495 1150 1600 2000 13.2
23940CC/W33 200x280x60 495 1150 1600 2000 13
23340CA/W33 200x420x165 2020 3500 750 950 125
23340MB/W33 200x420x165 2020 3500 750 950 125
24140CA/W33 200x340x140 1630 2450 900 1200 53.5
24140MB/W33 200x340x140 1630 2450 900 1200 53.5
24140CC/W33 200x340x140 1630 2450 900 1200 53.1
24040CA/W33 200x310x109 985 2130 900 1200 31.3
24040MB/W33 200x310x109 985 2130 900 1200 31.3
24040CC/W33 200x310x109 985 2130 900 1200 31
22240CA/W33 200x360x98 1100 1950 1100 1500 44.7
22240MB/W33 200x360x98 1100 1950 1100 1500 44.7
22240CC/W33 200x360x98 1100 1950 1100 1500 44.1
22340CA/W33 200x420x138 1740 2860 850 1100 97
22340MB/W33 200x420x138 1740 2860 850 1100 97
22340CC/W33 200x420x138 1740 2860 850 1100 96.6
23044CA/W33 220x340x90 935 1900 1100 1500 32
23044MB/W33 220x340x90 935 1900 1100 1500 32
23044CC/W33 220x340x90 935 1900 1100 1500 31.7
23144CA/W33 220x370x120 1370 2710 900 1200 54.7
23144MB/W33 220x370x120 1370 2710 900 1200 54.7
23144CC/W33 220x370x120 1370 2710 900 1200 54.4
23244CA/W33 220x400x144 1720 3200 750 950 77.3
23244MB/W33 220x400x144 1720 3200 750 950 77.3
23244CC/W33 220x400x144 1720 3200 750 950 77
23944CA/W33 220x300x60 500 980 1520 1760 12.5
23944MB/W33 220x300x60 500 980 1520 1760 12.5
23944CC/W33 220x300x60 500 980 1520 1760 12.1
24144CA/W33 220x370x150 1920 3045 800 1000 67
24144MB/W33 220x370x150 1920 3045 800 1000 67
24144CC/W33 220x370x150 1920 3045 800 1000 66.6
24044CA/W33 220x340x118 1150 2500 850 1100 39.1
24044MB/W33 220x340x118 1150 2500 850 1100 39.1
24044CC/W33 220x340x118 1150 2500 850 1100 38.7
22244CA/W33 220x400x108 1350 2400 950 1300 63.5
22244MB/W33 220x400x108 1350 2400 950 1300 63.5
22244CC/W33 220x400x108 1350 2400 950 1300 63.1
22344CA/W33 220x460x145 2450 3130 800 1000 115
22344MB/W33 220x460x145 2450 3130 800 1000 115
22344CC/W33 220x460x145 2450 3130 800 1000 115
23048CA/W33 240x360x92 985 2080 1000 1400 34.2
23048MB/W33 240x360x92 985 2080 1000 1400 34.2
23048CC/W33 240x360x92 985 2080 1000 1400 34
23148CA/W33 240x400x128 1500 3000 850 1100 68.2
23148MB/W33 240x400x128 1500 3000 850 1100 68.2
23148CC/W33 240x400x128 1500 3000 850 1100 68
23248CA/W33 240x440x160 2080 3950 750 900 102
23248MB/W33 240x440x160 2080 3950 750 900 102
23248CC/W33 240x440x160 2080 3950 750 900 102
23948CA/W33 240x320x60 530 1310 1300 1700 15
23948MB/W33 240x320x60 530 1310 1300 1700 15
23948CC/W33 240x320x60 530 1310 1300 1700 14.7
24148CA/W33 240x400x160 1660 3400 800 1000 79
24148MB/W33 240x400x160 1660 3400 800 1000 79
24148CC/W33 240x400x160 1660 3400 800 1000 78.6
24048CA/W33 240x360x118 1240 2800 900 1200 46.5
24048MB/W33 240x360x118 1240 2800 900 1200 46.5
24048CC/W33 240x360x118 1240 2800 900 1200 46.1
22248CA/W33 240x440x120 1640 1820 850 1150 85
22248MB/W33 240x440x120 1640 1820 850 1150 85
22248CC/W33 240x440x120 1640 1820 850 1150 84.8
22348CA/W33 240x500x155 2480 3200 750 1000 150
22348MB/W33 240x500x155 2480 3200 750 1000 150
22348CC/W33 240x500x155 2480 3200 750 1000 149
US $415-450
/ Piece
|
1 Piece

(Min. Order)

###

Rolling Body: Roller Bearings
The Number of Rows: Double
Outer Dimension: Extra Large (440mm)
Material: Bearing Steel
Spherical: Aligning Bearings
Load Direction: Radial Bearing

###

Samples:
US$ 415/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:

###

Bearing NO.  
New : 23248CA/W33
Old : 3053248KH
Boundary dimensions(mm)  
d : 240
D : 440
B : 160
r 1.2min : 4
Basic load ratings(kN)  
Cr : 2440
Cor : 4050
Limiting speed(rpm)  
Grease : 630
Oil : 800
Abutment and fillet dimensions(mm)  
da min : 258
Da max : 422
ra max : 3
Value  
e : 0.37
Y1 : 1.8
Y2 : 2.7
Y0 : 1.8
Weight (kg)  
Refer : 106

###

Bearing No. Boundary Dimensions  Basic Loading(kN)  Limiting Speed(rpm) Mass(kg)
  dxDxB Dy.(Cr) Sta.(Cor) Grease Oil  
23034CA/W33 170x260x67 555 1090 1600 2000 14.2
23034MB/W33 170x260x67 555 1090 1600 2000 14.2
23034CC/W33 170x260x67 555 1090 1600 2000 14
23134CA/W33 170x280x88 730 1390 1200 1600 26.1
23134MB/W33 170x280x88 730 1390 1200 1600 26.1
23134CC/W33 170x280x88 730 1390 1200 1600 25.6
23234CA/W33 170x310x110 1070 1930 950 1300 38
23234MB/W33 170x310x110 1070 1930 950 1300 38
23234CC/W33 170x310x110 1070 1930 950 1300 37.5
23934CA/W33 170x230x45 400 800 1800 2400 5.45
23334CA/W33 170x360x136 1420 2250 900 1200 68.7
23334MB/W33 170x360x136 1420 2250 900 1200 68.7
24134CA/W33 170x280x109 915 1830 1000 1400 24.8
24134MB/W33 170x280x109 915 1830 1000 1400 24.8
24134CC/W33 170x280x109 915 1830 1000 1400 24.1
24034CA/W33 170x260x90 705 1500 1000 1400 17.8
24034MB/W33 170x260x90 705 1500 1000 1400 17.8
24034CC/W33 170x260x90 705 1500 1000 1400 17.1
22234CA/W33 170x310x86 845 1450 1300 1700 26.8
22234MB/W33 170x310x86 845 1450 1300 1700 26.8
22234CC/W33 170x310x86 845 1450 1300 1700 26.1
22334CA/W33 170x360x120 1320 2120 950 1300 62.6
22334MB/W33 170x360x120 1320 2120 950 1300 62.6
22334CC/W33 170x360x120 1320 2120 950 1300 62.1
23036CA/W33 180x280x74 630 1280 1400 1800 17.7
23036MB/W33 180x280x74 630 1280 1400 1800 17.7
23036CC/W33 180x280x74 630 1280 1400 1800 17.4
23136CA/W33 180x300x96 900 1720 1100 1500 27.1
23136MB/W33 180x300x96 900 1720 1100 1500 27.1
23136CC/W33 180x300x96 900 1720 1100 1500 26.6
23236CA/W33 180x320x112 1160 2130 900 1200 38.7
23236MB/W33 180x320x112 1160 2130 900 1200 38.7
23236CC/W33 180x320x112 1160 2130 900 1200 38.4
23936CA/W33 180x250x52 430 830 1700 2200 7.34
23936CC/W33 180x250x53 430 830 1700 2200 7.34
24136CA/W33 180x300x118 1020 2030 900 1200 33
24136MB/W33 180x300x118 1020 2030 900 1200 33
24136CC/W33 180x300x118 1020 2030 900 1200 32.7
24036CA/W33 180x280x100 835 1750 950 1300 26.6
24036MB/W33 180x280x100 835 1750 950 1300 26.6
24036CC/W33 180x280x100 835 1750 950 1300 26.2
22236CA/W33 180x320x86 895 1550 1300 1700 29.4
22236MB/W33 180x320x86 895 1550 1300 1700 29.4
22236CC/W33 180x320x86 895 1550 1300 1700 29.1
22336CA/W33 180x380x126 1470 2400 900 1200 72.2
22336MB/W33 180x380x126 1470 2400 900 1200 72.2
22336CC/W33 180x380x126 1470 2400 900 1200 72
23038CA/W33 190x290x75 700 1450 1300 1700 17.3
23038MB/W33 190x290x75 700 1450 1300 1700 17.3
23038CC/W33 190x290x75 700 1450 1300 1700 17.1
23138CA/W33 190x320x104 975 1840 1000 1400 34.3
23138MB/W33 190x320x104 975 1840 1000 1400 34.3
23138CC/W33 190x320x104 975 1840 1000 1400 34
23238CA/W33 190x340x120 1290 2400 850 1100 44.8
23238MB/W33 190x340x120 1290 2400 850 1100 44.8
23238CC/W33 190x340x120 1290 2400 850 1100 44.4
23938CA/W33 190x260x52 550 980 1500 2000 8.32
23938CC/W33 190x260x52 550 980 1500 2000 8.01
24138CA/W33 190x320x128 1200 2400 850 1100 41.9
24138MB/W33 190x320x128 1200 2400 850 1100 41.9
24138CC/W33 190x320x128 1200 2400 850 1100 41.5
24038CA/W33 190x290x100 855 1840 950 1300 22.9
24038MB/W33 190x290x100 855 1840 950 1300 22.9
24038CC/W33 190x290x100 855 1840 950 1300 22.5
22238CA/W33 190x340x92 865 1620 1200 1600 37.4
22238MB/W33 190x340x92 865 1620 1200 1600 37.4
22238CC/W33 190x340x92 865 1620 1200 1600 37
22338CA/W33 190x400x132 1640 2630 850 1100 82.2
22338MB/W33 190x400x132 1640 2630 850 1100 82.2
22338CC/W33 190x400x132 1640 2630 850 1100 82
23040CA/W33 200x310x82 770 1560 1200 1600 22.6
23040MB/W33 200x310x82 770 1560 1200 1600 22.6
23040CC/W33 200x310x82 770 1560 1200 1600 22.1
23140CA/W33 200x340x112 1170 2240 950 1300 43.8
23140MB/W33 200x340x112 1170 2240 950 1300 43.8
23140CC/W33 200x340x112 1170 2240 950 1300 43.1
23240CA/W33 200x360x128 1360 2530 850 1100 53.4
23240MB/W33 200x360x128 1360 2530 850 1100 53.4
23240CC/W33 200x360x128 1360 2530 850 1100 53.1
23940CA/W33 200x280x60 495 1150 1600 2000 13.2
23940MB/W33 200x280x60 495 1150 1600 2000 13.2
23940CC/W33 200x280x60 495 1150 1600 2000 13
23340CA/W33 200x420x165 2020 3500 750 950 125
23340MB/W33 200x420x165 2020 3500 750 950 125
24140CA/W33 200x340x140 1630 2450 900 1200 53.5
24140MB/W33 200x340x140 1630 2450 900 1200 53.5
24140CC/W33 200x340x140 1630 2450 900 1200 53.1
24040CA/W33 200x310x109 985 2130 900 1200 31.3
24040MB/W33 200x310x109 985 2130 900 1200 31.3
24040CC/W33 200x310x109 985 2130 900 1200 31
22240CA/W33 200x360x98 1100 1950 1100 1500 44.7
22240MB/W33 200x360x98 1100 1950 1100 1500 44.7
22240CC/W33 200x360x98 1100 1950 1100 1500 44.1
22340CA/W33 200x420x138 1740 2860 850 1100 97
22340MB/W33 200x420x138 1740 2860 850 1100 97
22340CC/W33 200x420x138 1740 2860 850 1100 96.6
23044CA/W33 220x340x90 935 1900 1100 1500 32
23044MB/W33 220x340x90 935 1900 1100 1500 32
23044CC/W33 220x340x90 935 1900 1100 1500 31.7
23144CA/W33 220x370x120 1370 2710 900 1200 54.7
23144MB/W33 220x370x120 1370 2710 900 1200 54.7
23144CC/W33 220x370x120 1370 2710 900 1200 54.4
23244CA/W33 220x400x144 1720 3200 750 950 77.3
23244MB/W33 220x400x144 1720 3200 750 950 77.3
23244CC/W33 220x400x144 1720 3200 750 950 77
23944CA/W33 220x300x60 500 980 1520 1760 12.5
23944MB/W33 220x300x60 500 980 1520 1760 12.5
23944CC/W33 220x300x60 500 980 1520 1760 12.1
24144CA/W33 220x370x150 1920 3045 800 1000 67
24144MB/W33 220x370x150 1920 3045 800 1000 67
24144CC/W33 220x370x150 1920 3045 800 1000 66.6
24044CA/W33 220x340x118 1150 2500 850 1100 39.1
24044MB/W33 220x340x118 1150 2500 850 1100 39.1
24044CC/W33 220x340x118 1150 2500 850 1100 38.7
22244CA/W33 220x400x108 1350 2400 950 1300 63.5
22244MB/W33 220x400x108 1350 2400 950 1300 63.5
22244CC/W33 220x400x108 1350 2400 950 1300 63.1
22344CA/W33 220x460x145 2450 3130 800 1000 115
22344MB/W33 220x460x145 2450 3130 800 1000 115
22344CC/W33 220x460x145 2450 3130 800 1000 115
23048CA/W33 240x360x92 985 2080 1000 1400 34.2
23048MB/W33 240x360x92 985 2080 1000 1400 34.2
23048CC/W33 240x360x92 985 2080 1000 1400 34
23148CA/W33 240x400x128 1500 3000 850 1100 68.2
23148MB/W33 240x400x128 1500 3000 850 1100 68.2
23148CC/W33 240x400x128 1500 3000 850 1100 68
23248CA/W33 240x440x160 2080 3950 750 900 102
23248MB/W33 240x440x160 2080 3950 750 900 102
23248CC/W33 240x440x160 2080 3950 750 900 102
23948CA/W33 240x320x60 530 1310 1300 1700 15
23948MB/W33 240x320x60 530 1310 1300 1700 15
23948CC/W33 240x320x60 530 1310 1300 1700 14.7
24148CA/W33 240x400x160 1660 3400 800 1000 79
24148MB/W33 240x400x160 1660 3400 800 1000 79
24148CC/W33 240x400x160 1660 3400 800 1000 78.6
24048CA/W33 240x360x118 1240 2800 900 1200 46.5
24048MB/W33 240x360x118 1240 2800 900 1200 46.5
24048CC/W33 240x360x118 1240 2800 900 1200 46.1
22248CA/W33 240x440x120 1640 1820 850 1150 85
22248MB/W33 240x440x120 1640 1820 850 1150 85
22248CC/W33 240x440x120 1640 1820 850 1150 84.8
22348CA/W33 240x500x155 2480 3200 750 1000 150
22348MB/W33 240x500x155 2480 3200 750 1000 150
22348CC/W33 240x500x155 2480 3200 750 1000 149

Types of Ball Bearings

If you’re looking to purchase a new ball bearing, there are many different types available. Learn about Single-row designs, Ceramic hybrid bearings, and Self-aligning ball bearings. You can also choose from stainless steel or single-row designs. Then, read about the different types of materials available to you. You’ll have an easier time making a decision. After all, you won’t have to worry about maintaining your new ball bearing, since it will be maintained by your supplier.
bearing

Single-row designs

Ball bearings with a single-row design have a high load-carrying capacity. They are used in applications where high loads must be handled smoothly. A single-row design is a good choice when the material’s properties require high load-carrying capacity but limited axial load capability. Single-row designs use two bearings with similar design features, but they have different mounting methods. Single-row designs can be adjusted either against one another to accommodate axial loads.
The single-row design is suitable for high-speed applications, but also has some disadvantages. The contact angle a is the angle between the radial plane and contact line. The larger the angle, the higher the axial load carrying capacity of the bearing. Single-row angular contact ball bearings are suitable for higher axial forces. Single-row angular contact ball bearings have a single-row design and support high axial forces in one direction. Single-row ball bearings are available in both pressed steel and machined steel cages.
Angular contact ball bearings with a single row feature a cage made of fiber-glass reinforced polyamide 66. These are available in diameters up to 130 mm. Four-point angular contact ball bearings use brass, steel, or brass plate. They have good running properties and a low coefficient of linear expansion. Single-row designs are easy to mount and are widely available. Alternatively, they can be mounted with a universal match design, which allows them to be easily adjusted.
One-row angular contact ball bearings are generally not suitable for angular misalignments because they are unsuitable for compensation of angular misalignments. Misalignments cause internal forces in the bearing which reduce its radial load capacity and life expectancy. This type of bearing is not suitable for adjacent mounting as it increases the chances of misalignment. However, it is a suitable choice for applications where only one bearing is required per bearing position.

Ceramic hybrid bearings

While all-ceramic bearings are limited to very specialized applications, Si3N4-based hybrid bearings are finding use in a wide range of high-speed machines. Compared to steel, ceramics are less susceptible to centrifugal forces, which are directly proportional to the mass of the balls. Because Si3N4 replacement balls have a lower density than steel, these bearings reduce the stress placed on the outer race.
The benefits of hybrid bearings are clear: they allow for higher speeds and loads than full-ceramic bearings, and they require no lubrication. Because of their many benefits, many industrial equipment operators are switching to these innovative bearings. CBR is one company that specializes in ceramic hybrid bearings and can help you find the best product for your application. If you are thinking about purchasing ceramic bearings for your next machine, here are some things you need to know about them.
A ceramic ball bearing surface has an extremely low coefficient of friction, which is important for applications that require low friction and high speeds. Ceramic balls also have a higher hardness than steel balls, which increases their life. In addition to this, ceramic hybrid bearings have superior thermal properties, generating less heat even when spinning at high speeds. These properties make ceramic hybrid bearings an ideal choice for high-speed machinery, especially electric motors. They are also suitable for applications that operate under water.
A ceramic ball hybrid bearing is much less susceptible to temperature fluctuations and wear. Because they are essentially indestructible, ceramic balls do not generate wear particles from the adhesive wear. They can run at significantly higher speeds than steel balls. Ceramic balls are also more resistant to moisture. For this reason, grease is a recommended lubricant in most ceramic bearing applications. These lubricants offer superior protection against moisture and corrosion. Further, they are available in many types.
bearing

Self-aligning ball bearings

A self-aligning ball bearing is one type of self-aligning bearing. These bearings are recommended for use in flex shaft systems. Their self-aligning feature prevents them from misaligning when in use. They can be used in both single and multiple-joint systems. In addition to self-aligning ball bearings, these units also feature flex shafts.
These self-aligning ball bearings come in a variety of configurations, including cylindrical, round, tapered, and straight bore. Their inner ring is tapered to meet specific tolerances. They are suitable for operating temperatures ranging from -30°F to 120°F. Their wide range of applications allows them to be used in general machinery, precision instruments, and low noise motors. In addition, they are available in a variety of outside diameters, widths, and internal clearances.
Self-aligning ball bearings have two rows of balls and one common sphered raceway in the outer ring. This enables them to automatically compensate for angular misalignment, which may be caused by machining and assembly errors or deflections. Compared to spherical roller bearings, these self-aligning ball bearings generate less friction. They run cooler even at high speeds. Self-aligning ball bearings also offer free engineering support.
Self-aligning ball bearings are designed for difficult shaft alignment. They are double-row, self-retaining units, with cylindrical or tapered bores. These bearings are available in open and sealed designs, and can also be used in applications with misalignment. They are also available with an outer ring that rotates in relation to the inner ring. When it comes to shaft misalignment, self-aligning ball bearings are a great solution.

Stainless steel

Stainless steel is a metal that resists corrosion and is highly durable. Its corrosion-resistant and water-resistance properties make it a good choice for bearings in food and marine applications. Additionally, stainless steel has hygienic benefits. Here are some of the benefits of stainless steel ball bearings. Read on to learn more about these amazing bearings! We’ve included some of the most common uses for stainless steel.
Hardness is important in a ball bearing. Steel uses the Rockwell C scale to measure hardness. A grade 25 steel ball bearing is accurate to 25 millionths of an inch, while a grade five ceramic bearing is less than a half-inch round. Although roundness is important, it shouldn’t be overemphasized, as the bearing surfaces may not be as accurate as the grade of the metal. And remember, a higher price tag doesn’t mean a better product.
Stainless steel ball bearings are available in a variety of alloys. The alloys used in manufacturing a stainless steel ball bearing vary in hardness, strength, and ductility. Stainless steel ball bearings have high corrosion-resistance properties. Additionally, they have long lubrication lives. These benefits make them a popular choice for industrial applications. These bearings are easy to maintain, reduce replacement costs, and offer corrosion resistance.
The NTN Sentinel Series is a premium line of stainless steel bearings. The solid lube is NSF H1 registered and prevents grease from leaching into food. It is also corrosion-resistant and doesn’t need to be coated. The seals and slinger create a water-resistant barrier between the steel ball and the lubricant. It also adds safety and security to the bearing.
bearing

Plastic balls

For applications where noise and weight are major concerns, plastic balls are ideal. These non-magnetic balls are ideal for MRI X-ray machines and sensors. They are also easy to lubricate, and are non-magnetic. A polymer ball bearing is the lightest of all three types. This makes them a good choice for many industries. Read on to learn more. This article will introduce some of the advantages of plastic balls for ball bearings.
Although ceramic ball bearings are more durable and offer many advantages, they are more expensive than plastic. Fortunately, plastic ball bearings offer a cheaper alternative. These bearings feature all-plastic races and cages. Depending on the application, plastic balls can be used in applications involving chemicals. In these cases, plastic ball bearings are available with a C160 grade, which is safe for use in temperatures below 176 deg F.
Medical devices often require precision specialty balls, which are made of glass, stainless steel, and plastic. These bearings must meet stringent cleanliness requirements. To meet the most stringent requirements, they must undergo ultrasonic cleaning. These bearings are available in plastic raceways, and are also available with glass or stainless steel balls. Polyethylene balls are lightweight and can be used in a variety of applications. They can be ordered in different sizes and tolerances to meet specific requirements.
Plastic balls for ball bearings are often mounted into other parts, such as plastic wheels, pulleys, and housings. They can be seamlessly integrated into other parts of a machine, which reduces assembly time and improves affordability. One important advantage of plastic bearings is that they are rust-resistant. As such, they can be used in harsh environments without causing any damage. If a piece of equipment is exposed to extreme temperatures, polymers are the ideal choice.

China Double Row Spherical Roller Bearing with Brass Cage NTN NSK Koyo NACHI Timken Bearing 23248 Ca/W33     bearing blockChina Double Row Spherical Roller Bearing with Brass Cage NTN NSK Koyo NACHI Timken Bearing 23248 Ca/W33     bearing block
editor by czh 2023-01-12

Recent Posts